The writer is making several great points regarding Installing A Bathtub overall in this article underneath.
Mounting a bath tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is conveniently obtainable, the project can move speedily; if you need to open up a wall surface to eliminate the old tub and also place the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need an assistant to vacate the old bathtub and embeded in the new one. Make sure you have actually certified on your own for the task and also are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to think about employing one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new bathtub in your washroom if you have already gotten a brand-new tub as well as do not require to change the arrangement of your previous water supply pipes.
Your tools as well as product list should comprise the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its last setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome due to the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, place the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the water as well as check all joints as well as new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bath tub should wait up until the tub has actually been made use of at the very least when as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bathroom as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break fairly very early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about A Step-by-Step Guide to Installing a Bathtub? Post feedback further down. We will be interested to listen to your thinking about this posting. In hopes that you visit us again later on. Sharing is good. Helping others is fun. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Go Deal Now